QUALITY AND PROPERTIES

• Excellent penetration in tricky cavities
• Elimination and displacement of water already present
• Easy application
• Auto-repair of existing minor damage by water displacement
• Corrosion protection
• Water-repellent
• Excellent adhesion
• Aromatic free quality
• Resistant to weather effects, weak acids and alkalines
• Cannot be painted over with lacquer
• Cleaning: fresh material with solvent, dry material mechanically

PHYSICAL AND CHEMICAL DATA

Spray gun can:

• Basis: waxes, additives, free of aromatic solvents
• Colour: brown
• Consistency: liquid
• Smell: solvent
• VOC-Content: approx. 0.3230 kg
• Salt spray test (DIN 50021): >1000 hours, Ri 0 at 100µ dry layer
• Chemical resistance against: water, salt spray, oil, weak acids and bases
• Temperature resistance (cured): -25°C - +180°C
• Working temperature: +15°C - +25°C, best results at room temperature
• Efficiency (1 coat): coat thickness ±200µ dry approx.  ±0,2 ltr/m²
• Drying time (20°C, 65% RV):
  Dust-dry: after approx. 105 minutes
  Completely dried: after approx. 5 h
  The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.
• Specific density (20°C) (nach DIN 51757): 0.87 - 0.89 kg/ltr.
• Storage stability:
  5 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
• Size:
  spray gun can, maximum nominal volume 1000 ml

USING INSTRUCTIONS

The most presto spray paints have a so-called no-spray ring or a tamper-proof cap. This is to avoid unauthorized use. Please see the corresponding advises on the cap or on the label.
Before use, carefully read and observe the warning texts on the labels!

Application spray gun can:

• For best results bring can to room temperature.
• The product is ready-to-use, no thinner necessary.
• Clean the spray gun with white spirit

TIPS FOR SPRAY PAINTING

Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.

The aerosol can should have room temperature.

Temperature should range between +10°C and +25°C, max. air humidity 60 %.

Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!

ORDER INFORMATION

Color	Product	Bundle	Art.No.
	presto Hohlraumschutz 1000	1 l	603277
	presto Hohlraumschutz 500	500 ml	306055

ENVIRONMENT AND LABELLING

Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". 

Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II,