SikaGard 6470 Stone chip protection grey 1L

SikaGard 6470 Stone chip protection 1L

SikaGard®-6470 gray sprayable anti-abrasive protection of the lower parts of the bodywork, repaintable

Technical data:
chemical base synthetic rubber
color black, gray, white
dry curing mechanism
density (liquid) (ISO 12185) ca 1.02 kg/l
solids content (ISO 3251) approx. 50%
viscosity ( Brookfield ) v= 0.5, spindle 5 ca 48 Pa.s
application temperature 20°C to 30°C
surface drying time approx. 45 min
total curing time at room temperature. approx. 120 min
at 60°C: approx. 45 min
temperature resistance (permanent) -25°C to 80°C
shelf life (between +10°C and +30°C) 24 months

measured at 23°C and 50% relative humidity (layer thickness 600μm)

Description:
SikaGard®-6470 is a durable protective product based on synthetic rubbers with a high effect against the abrasive action of gravel and high anti-corrosion protection. The preparation has excellent damping properties and a short curing time. SikaGard®-6470 is manufactured in accordance with ISO 9001/14001 quality systems.

Product advantages:
- paintable
- application without overspray
- high resistance to abrasive damage
- flexible film after drying

Fields of application:
SikaGard®-6470 provides a high protective effect against the abrasive action of gravel and anti-corrosion protection, applicable to all parts of the body, especially to the thresholds and
wheel arches, lower parts of doors, etc.. The preparation has excellent damping properties, short curing time. Different surface textures can be achieved by spraying. After hardening, it can be painted over with all paint systems.
SikaGard®-6470 exhibits very good adhesion properties to various metal substrates and PVC. The product is intended for processing by professional and experienced users.

Chemical resistance:
When cured, SikaGard®-6450 is resistant to water, seawater, salt water solutions, oils and weak acid concentrations. These data are due to
for a wide range of influencing materials and conditions only indicative. The binding assessment is conditioned by an object test.

Processing instructions:
Preparation of the substrate: treated surfaces must be clean, dry, without traces of fats, oils, waxes or other separating substances. You can request detailed information on the use of the product from the supplier or from Sika's technical service.

Application
SikaGard®-6470 can be applied by spraying with low-pressure airless systems or low-pressure air guns with a pressure of approx. 3-6 bar. Before application, it is necessary to shake the can well
shake Apply at room temperature. Spray from a distance of approx. 30 cm with X movement of the gun in the form of continuous spraying. If a thicker layer is needed, it is necessary to spray in several layers and let the previous one dry sufficiently. Unprocessed spray must be tightly closed immediately after application, it can only be stored for a short time. Removal of residues: Fresh SikaGard®-6470 can be cleaned from soiled surfaces and tools before it hardens with Sika® Remover 208. Hardened material can only be removed mechanically. Hands can be cleaned using a Sika®Handclean towel or washing paste and rinsing with water.

Packaging:
can 1000 ml

For professional use only

Danger
H225 Highly flammable liquid and vapour. H315 Irritating to skin. H336 May cause drowsiness or dizziness. H411 Toxic to aquatic organisms, with long-term effects.
P210 Keep away from heat, hot surfaces, sparks, open flames and other sources of ignition. No smoking. P233 Keep container tightly closed. P261 Avoid breathing dust/fume/gas/mist/vapour/aerosols. P273 Avoid release to the environment.
P370 + P378 In case of fire: Extinguish with sand, dry chemical or alcohol-resistant foam. P391 Collect spilled product.