Alkyton Primer+ 750 ml

Fast variant of Alkyton coating.

Need to finish in one day? Is 16 hours waiting for the second coat much? Then there is a 'quick fix'. Use Primer + and you can paint a second coat in two hours.

Ideal for fast application, for older galvanized or fine corrosion (fox).


Spreading capacity of 12 m2 per liter at one layer (35 µm).


CHARACTERISTICS AND QUALITY
Special base containing solvents
For brush application
Creates an ideal anti-corrosive substrate
Use on new, blasted or slightly corroded steel surfaces
The product has very fast drying even at low temperatures

PHYSICAL AND CHEMICAL PROPERTIES
Binder: modified alkyd resin
Colors: red / gray
Odor: solvent
Spreading capacity: Theoretical: 12 m² / l / at 35 μm dry film
Practical spreading rates depend on many factors such as surface texture and application losses
Drying (at 20 ° C, 50% RH):
To touch: 1 hr.
For handling: 2 hours
Fully cured: 8 days
Recoatable: after 2 hours
Specific Gravity: 1.2 kg / ltr.
Viscosity: 80-85 KU 20 ° C
Dry matter: 42% by volume, 60% by weight
Temperature resistance: up to 120 ° C
Shelf life:
5 years from date of manufacture in unopened cans, when stored in dry, well ventilated areas not exposed to direct sunlight at temperatures between 5 ° C and 35 ° C.
Recycling: Place the empty container in the waste container. Hand in at a special hazardous waste center.
Packaging: max. Nominal volume = 250 ml, 750 ml and 5 ltr


ENVIRONMENT AND LABELS
Environmentally friendly: MOTIP DUPLI products are 100% heavy metal free. Lids and packaging are made of recyclable materials.

Waste disposal: Mix waste and contaminated packaging as hazardous waste. Cleaned packaging can be handed over for recycling.

Packaging Marking: All MOTIP DUPLI products comply with the current Czech and EU regulations concerning packaging marking. These are the current versions of the following regulations:

Act No. 350/2011 Coll. on Chemical Substances and Chemical Mixtures and on Amendments to Certain Acts (Chemical Act).
Regulation (EC) No 1272/2008 of the European Parliament and of the Council on classification, labeling and packaging of substances and mixtures (CLP).
Government Regulation No. 194/2001 Coll., Laying down technical requirements for aerosol dispensers (in case of aerosol)
Directive 75/324 / EEC (ADD) - in the case of aerosol
The Safety Data Sheets for MOTIP DUPLI products comply with REACH 1907/2006 / EC, Article 31, Annex II.


PREPARATION BEFORE PAINTING
Preparation:

Remove oil, grease and any other surface contamination with alkaline RO ND 14 or pressure cleaning in combination with suitable detergents
For optimum results, remove scales, loose rust and poorly adhering old paint blast to Sa 2 1/2 grade (ISO 8501 - 1: 1988) If blast cleaning is not possible, use a scraper and a St 3 grade steel brush (ISO 8501 - 1: (1988)
The surface must be dry and clean during application
Painting:

Mix thoroughly before use
Brush:
Dilution of max. 10% RO 633 (or S6005) Two brushes may be necessary to achieve the desired coating thickness. Use a natural long hair brush
Roller:
10% thinner RO 633 (or S6005) Two brushes may be required to achieve the desired coating thickness. Use pearl rollers 8-12 with medium pile
Air Spraying:
Dilution 10 -20% by volume RO 641 - in small quantities according to the equipment. Nozzle size 1.2 - 1.8 mm, pressure 2 - 4 bar
Without air spraying:
Thinner RO 641 - in small quantities according to the equipment. Nozzle size 0.013 - 0.015 inch, pressure 130-200 bar
cleaning:

Thinner S 6005
Application conditions:

Surface and material air temperatures between 5 ° and 35 ° C
Relative humidity: below 85%
Lowest substrate temperature: 3 ° C above dew point