ColorWorks RAL 9005 black matte spray paint 400ml

High gloss and satin matt colours, excellently suitable for all DIY and handicraft works on wood, metal, aluminium, glass, stone, carton, paper, eternite, china and many paintable plastics. For indoor and outdoor applications.

Quality and properties
High-grade synthetic quality
Quick-drying
Suitable to paint and repair indoor and outdoor objects
Good coverage and filling power
Good colour and gloss retention
Weather resistant, light-proof, UV-resistant
Excellent flow for even surfaces
Good adherence on nearly all materials
Scratch-, bump and shock-proof
Temporarily resistant against fuel, chemicals and weather influences

Physical and chemical data
Basis of the binder: Alkyd resin
Colour: specific
Smell: solvent
Degree of gloss (at measurement angle 60° acc. to DIN 67530):
glossy: 85-90 gloss units
satin matt: 30-35 gloss units
Efficiency:
Depending on consistence and color of the ground:
400 ml are sufficient for approx. 0.8 - 1.2 m²
depending on colour
Drying time (at 20°C, 50% relative air humidity):
Dust-dry: after approx. 30 minutes
Non-sticky: after approx. 4 hours
Cured: after approx. 24 hours
Coatable: within 2 hours or after approx. 24 hours
The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.
Temperature-resistant: up to 80°C
Storage stability:
Aerosols: 10 years, if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)

Size: aerosol cans, maximum nominal volume 400 ml

Instruction manuel
The most MoTip spray paints have a so-called no-spray ring or a tamper-proof cap. This is to avoid unauthorized use. Please see the corresponding advises on the cap or on the label.
Before use, carefully read and observe the warning texts on the label!
Preparation of the ground:

The ground has to be clean, dry and free from fat.
Remove residues of old paintings and rust, then sand and prime.
Plastic Parts have to be primed with MoTip Plastic Primer.
Let dry for 1 - 2 hours.
 

Lacquering:

The ground has to be clean, dry and free from fat.
Bring the can to room temperature.
Processing temperature during 15 - 25°C.
Mask off the areas which are not to be painted.
Before use, shake the can for 2 minutes.
Test compatibility of the spray at an invisible spot.
Spray from a distance of approx. 25 cm.
Spray several thin coats in 2 minute intervals.
Shake the can during use from time to time.
After use, turn the can upside down and spray to clean the valve.
Do not overpaint with acrylic or nitro combi paints - not even after curing!

Tips for spray painting
Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.

The aerosol can should have room temperature.

Temperature should range between +10°C and +25°C, max. air humidity 60 %.

Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!

Danger
acetone
Hydrocarbons, C9-C11, n-alkanes, isoalkanes, cyclics, aromatics (<2%)
H222-H229 Extremely flammable aerosol. The container is under pressure: it may burst when heated.
H319 Causes serious eye irritation.
H336 May cause drowsiness or dizziness.
P101 If medical attention is needed, have product container or label at hand.
P102 Keep out of reach of children.
P210 Keep away from heat, hot surfaces, sparks, open flames and other sources of ignition. No smoking.
P211 Do not spray on open flames or other sources of ignition.
P251 Do not puncture or burn even after use.
P260 Do not breathe aerosols.
P410+P412 Protect from sunlight. Do not expose to temperatures exceeding 50°C.
P501 Dispose of contents / container in accordance with local regulations.
EUH066 Repeated exposure may cause skin dryness or cracking. Explosive mixtures can form without sufficient ventilation.
EUH211 Attention! Hazardous respirable droplets may form when sprayed. Do not inhale aerosols or mist.