QUALITY AND PROPERTIES

• High-grade, quick-drying nitro-combi paint
• Good flow, smooth surface
• Weather-resistant, light-proof, UV-resistant (non-yellowing)
• Limited fuel-resistance
• Good colour- and gloss retention
• Hard surface, abrasion-resistant

PHYSICAL AND CHEMICAL DATA

• Basis of the binder: nitro-comib
• Colour: div. aluminium shades
• Smell: solvent
• Degree of gloss (at measurement angle 60° acc. to DIN 67530):
  satin matt: 50 - 60 gloss units
  glossy: 80 gloss units after coating with Clear Lacquer
• Efficiency:
  Depending on consistence and color of the ground:
  12 ml for small spots
  150 ml are sufficient for approx. 0.5 m²
• Drying time (at 20°C, 50% relative air humidity):
  Dust-dry: after approx. 10 minutes
  Dry to touch: after approx. 30 minutes
  Coatable with 2-Coat Clear Lacquer: after approx. 30 minutes
  Cured: after approx. 24 hours
  The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.
• Temperature-resistant: up to 80°C
• Storage stability:
  Aerosols: 10 years, touch-up pencils: 5 years, if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
• Size: touch-up pencils 12 ml, aerosol cans, maximum nominal volume 150 ml

USING INSTRUCTIONS

The most DUPLI-COLOR spray paints have a so-called no-spray ring or a tamper-proof cap. This is to avoid unauthorized use. Please see the corresponding advises on the cap or on the label.
Before use, carefully read and observe the warning texts on the label!

Application

Preparation of the ground:

• Carefully clean rims from dirt, fat and brake-dust. 
• Treat existing pore rust with presto Deruster.
• The ground has to be sanded, clean, dry and fat-free.
• Mask off the rim edges with masking tape.
• Use paper to protect surrounding area from spray-dust.
• Prime with DUPLI-COLOR Primer.
• After drying, slightly sand (sanding paper grain P600)

Lacquering:

• Before use, shake the can vigorously for 3 minutes.
• Test spray to check colour-matching.
• Spray several thin coats in 3 - 5 minute intervals from a distance of approx. 25 cm.
• After 30 minutes drying time, coat with DUPLI-COLOR Tuning Wheel Paint Clear Coat to protect the metal pigments in the lacquer.
• Do not spray over synthetic paints!

TIPS FOR SPRAY PAINTING

Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.

The aerosol can should have room temperature.

Temperature should range between +10°C and +25°C, max. air humidity 60 %.

Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!

ORDER INFORMATION

Color	Product	Bundle	Art.No.
	ALU WHEEL PAINT arctic 150	150 ml	665615
	ALU WHEEL PAINT argento 12	12 ml	665653
	ALU WHEEL PAINT argento 150	150 ml	665585
	ALU WHEEL PAINT artic 12	12 ml	665677
	ALU WHEEL PAINT quartz 12	12 ml	665691
	ALU WHEEL PAINT quartz 150	150 ml	665646
	ALU WHEEL PAINT viper 12	12 ml	665660
	ALU WHEEL PAINT viper 150	150 ml	665592

ENVIRONMENT AND LABELLING

Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". 

Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II,