QUALITY AND PROPERTIES

• High-grade nitro-combi quality
• Very good coverage
• Excellent adhesion
• Good flow, smooth surface
• Quick-drying
• Suitable for indoors and outdoors applications
• Weather-resistant, light-proof, UV-resistant
• Scratch-, shock- and impact-resistant
• High surface hardness and good elasticiy
• Polishable, dirt-resistand surface

PHYSICAL AND CHEMICAL DATA

• Basis of the binder: acryl resin
• Colour: black or white, glossy, satin mat or matt
• Smell: solvent
• Degree of gloss (at measurement angle 60° acc. to DIN 67530):
  glossy: 80-85 gloss units
  satin matt: 30-40 gloss units
  matt: 10-20 gloss units
• Efficiency:
  Depending on consistence and color of the ground:
  12ml for several applications
  150 ml are sufficient for approx. 0.5 m²
  500 ml are sufficient for approx. 1.5 - 2.0 m²
• Drying time (at 20°C, 50% relative air humidity):
  12 ml:
  Dust-dry: after approx. 15 minutes
  Dry to touch: after approx. 60 minutes
  150 ml / 500 ml:
  Dust-dry: after approx. 5-10 minutes
  Tack-free: after approx. 10-20 minutes
  Coatable: after approx. 2 hours
  The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.
• Temperature-resistant: up to 110°C
• Storage stability:
  touch-up pencils: 5 years, aerosols: 10 years, if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
• Size:
  touch-up pencils 12 ml,
  aerosol cans, maximum nominal volume 150 ml resp. 500 ml

INSTRUCTION MANUEL

Before use, carefully read and observe the warning texts on the label!

Preparation of the ground:

• Clean underground from dirt, fat and rust.
• Fill and sand uneven surfaces. 
• If no filling with putty is necessary, apply a primer, e.g. MoTip Rallye Primer.
• Otherwise apply MoTip Filler on the fine-sanded filled surfaces. Before that, generously mask off the repair spot.
• If bigger areas have to be repaired, we recommend to mask off edges of the car body.

Lacquering:

• The surface has to be clean, dry and free from fat.
• Mask off areas not to be painted.
• Before use, shake the can vigorously for 3 minutes.
• Test spray to check colour-matching.
• The spray distance should be approx. 20-30 cm.
• Spray several thin cross-coats in 3 - 5 minute intervals.
• Do not spray over synthetic paints!

TIPS FOR SPRAY PAINTING

Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.

The aerosol can should have room temperature.

Temperature should range between +10°C and +25°C, max. air humidity 60 %.

Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!

 

ENVIRONMENT AND LABELLING

Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". 

Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, 

Danger
acetone butyl acetate 2-Methoxy-1-methylethyl acetate
H222-H229 Extremely flammable aerosol. The container is under pressure: it may burst when heated. H319 Causes serious eye irritation. H336 May cause drowsiness or dizziness
P101 If medical attention is needed, have product container or label at hand. P102 Keep out of reach of children. P210 Keep away from heat, hot surfaces, sparks, open flames and other sources of ignition. No smoking. P211 Do not spray on open flames or other sources of ignition. P251 Do not puncture or burn even after use. P260 Do not breathe aerosols. P410+P412 Protect from sunlight. Do not expose to temperatures exceeding 50°C. P501 Dispose of contents / container in accordance with local regulations.
EUH066 Repeated exposure may cause skin dryness or cracking. Explosive mixtures can form without sufficient ventilation.