QUALITY AND PROPERTIES

• High-grade synthetic quality
• Transparent; the structure of the ground remains visible after coating
• Durable gloss
• Excellent adhesion
• Quick-drying
• Good flow, smooth surface
• Weather-resistant
• Very good colour retention (light-proof, non-yellowing)
• Scratch-, shock- and impact-resistant
• High surface hardness and good elasticiy
• Smooth, dirt-resistant surface

PHYSICAL AND CHEMICAL DATA

• Basis of the binder: alkyd resin
• Colour: colour-specific
• Smell: solvent
• Degree of gloss (at measurement angle 60° acc. to DIN 67530):
  glossy: 80-85 gloss units
• Efficiency:
  Depending on consistence and color of the ground:
  150 ml are sufficient for approx. 0.5 m²
  400 ml are sufficient for approx. 1.2 m²
• Drying time (at 20°C, 50% relative air humidity):
  Dust-dry: after approx. 30 minutes
  Tack-free: after approx. 2 hours minutes
  dry to touch: after approx. 4 hours
  The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.
• Temperature-resistant: up to 80°C
• Storage stability:
  10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
• Size:
  aerosol can, maximum nominal volume 150 ml resp. 400 ml

INSTRUCTION MANUEL

The most MoTip spray paints have a so-called no-spray ring or a tamper-proof cap. This is to avoid unauthorized use. Please see the corresponding advises on the cap or on the label.
Before use, carefully read and observe the warning texts on the label!

Application:

• Prime plastic parts with the colourless MoTip Plastic Primer.
• The surface has to be clean, dry and free from fat.
• Protect surrounding area from spray mist!
• Before use, shake the can vigorously for 3 minutes.
• The spray distance should be approx. 20-30 cm.
• Spray several thin coats in 3 - 5 minute intervals onto the dry repair spot, till the desired effect is achieved.
• Before lacquering lightening bulbs you should make a test, as the adhesion cannot be granted up to every temperature level. 
• Not re-sprayable with clear varnish.

TIPS FOR SPRAY PAINTING

Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.

The aerosol can should have room temperature.

Temperature should range between +10°C and +25°C, max. air humidity 60 %.

Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels! 

ORDER INFORMATIONS

Color	Product	Bundle	Art.No.
	Motip Tun. Backlight Black 150	150 ml	00160
	Motip Tun. Backlight Black 400	400 ml	00260
	Motip Tun. Backlight Red 150	150 ml	00161
	Motip Tun. Backlight Red 400	400 ml	00261

ENVIRONMENT AND LABELLING

Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". 

Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II,